High River General Hospital - Revision history

Alberta Fire Alarms at 05:50, 23 February 2025

2025-02-23T05:50:46Z

@@ Line 55: / Line 55: @@
 ==== EOLs ====
 There are Edwards EOL-P1 end of line resistor plates on the kitchen suppression circuit, and all sprinkler and signal circuits.
 [[Category:Alberta]]
 [[Category:Healthcare]]

Alberta Fire Alarms: /* Automatic Detection Devices */

2024-12-08T07:27:20Z

Automatic Detection Devices

← Older revision		Revision as of 01:27, 8 December 2024
Line 41:		Line 41:
	All aforementioned detectors are mounted on EST SIGA-SB bases.		All aforementioned detectors are mounted on EST SIGA-SB bases.

	There is a conventional heat detector in the gas meter room; model to be confirmed.		There is a conventional heat detector in the gas meter room; model to be confirmed, wired to an EST SIGA-CT1 addressable monitor module.

	There are EST SIGA-DH duct smoke detector housings with EST SIGA-PS addressable photoelectric heads and EST SIGA-SB bases on most air handling units: two on the second floor and one in the penthouse. The second floor duct smokes are equipped with EST SIGA-LED remote indicators, and the penthouse duct smoke is equipped with an Edwards 5956A remote indicator.		There are EST SIGA-DH duct smoke detector housings with EST SIGA-PS addressable photoelectric heads and EST SIGA-SB bases on most air handling units: two on the second floor and one in the penthouse. The second floor duct smokes are equipped with EST SIGA-LED remote indicators, and the penthouse duct smoke is equipped with an Edwards 5956A remote indicator.

TwentyThree33: /* Notification Appliances */

2024-12-06T19:20:13Z

Notification Appliances

← Older revision		Revision as of 13:20, 6 December 2024
Line 26:		Line 26:
	Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).		Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).

	Some areas have Edwards 439D-10AWC vibrating bells (10" gong) mounted remotely; ~~it is unknown if~~ these are in use ~~on the current system~~.		Some areas have Edwards 439D-10AWC vibrating bells (10" gong) mounted remotely, likely left over from the original system; these are still in use.
	===Initiating Devices===		===Initiating Devices===
	====Pull Stations====		====Pull Stations====
Line 41:		Line 41:
	All aforementioned detectors are mounted on EST SIGA-SB bases.		All aforementioned detectors are mounted on EST SIGA-SB bases.

	There are EST SIGA-DH duct smoke detector housings with EST SIGA-PS addressable photoelectric heads and EST SIGA-SB bases on most air handling units: two on the second floor and one in the penthouse. The second floor duct smokes ~~have~~ EST SIGA-LED remote indicators, and the penthouse duct smoke ~~has~~ an Edwards 5956A remote indicator.		There is a conventional heat detector in the gas meter room; model to be confirmed.

			There are EST SIGA-DH duct smoke detector housings with EST SIGA-PS addressable photoelectric heads and EST SIGA-SB bases on most air handling units: two on the second floor and one in the penthouse. The second floor duct smokes are equipped with EST SIGA-LED remote indicators, and the penthouse duct smoke is equipped with an Edwards 5956A remote indicator.
	====Modules====		====Modules====
	There are EST SIGA-CT1 addressable monitor modules supervising the kitchen suppression system and the sprinkler system’s tamper and flow switches.		There are EST SIGA-CT1 addressable monitor modules supervising the kitchen suppression system, and the sprinkler system’s tamper and flow switches.

	There are EST SIGA-CR addressable relay modules serving various purposes.		There are EST SIGA-CR addressable relay modules serving various purposes.
Line 52:		Line 54:

	==== EOLs ====		==== EOLs ====
	There are Edwards EOL-P1 end of line resistor plates on the kitchen suppression ~~signal~~ circuit, and all sprinkler and signal circuits.		There are Edwards EOL-P1 end of line resistor plates on the kitchen suppression circuit, and all sprinkler and signal circuits.
	[[Category:Alberta]]		[[Category:Alberta]]
	[[Category:Healthcare]]		[[Category:Healthcare]]

TwentyThree33 at 23:47, 2 December 2024

2024-12-02T23:47:30Z

← Older revision		Revision as of 17:47, 2 December 2024
Line 41:		Line 41:
	All aforementioned detectors are mounted on EST SIGA-SB bases.		All aforementioned detectors are mounted on EST SIGA-SB bases.

	There are EST SIGA-DH duct smoke detector housings with EST SIGA-PS addressable photoelectric heads and EST SIGA-SB bases on most air handling units: two on the second floor and one in the penthouse.		There are EST SIGA-DH duct smoke detector housings with EST SIGA-PS addressable photoelectric heads and EST SIGA-SB bases on most air handling units: two on the second floor and one in the penthouse. The second floor duct smokes have EST SIGA-LED remote indicators, and the penthouse duct smoke has an Edwards 5956A remote indicator.
	====Modules====		====Modules====
	There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.		There are EST SIGA-CT1 addressable monitor modules supervising the kitchen suppression system and the sprinkler system’s tamper and flow switches.

	There are EST SIGA-CR addressable relay modules serving various purposes.		There are EST SIGA-CR addressable relay modules serving various purposes.
Line 52:		Line 52:

	==== EOLs ====		==== EOLs ====
	There are Edwards EOL-P1 end of line resistor plates on all sprinkler and signal circuits.		There are Edwards EOL-P1 end of line resistor plates on the kitchen suppression signal circuit, and all sprinkler and signal circuits.
	[[Category:Alberta]]		[[Category:Alberta]]
	[[Category:Healthcare]]		[[Category:Healthcare]]

TwentyThree33: Doing the annual this week so I discovered additional stuff. Stay tuned for the original system!

2024-12-02T23:36:47Z

Doing the annual this week so I discovered additional stuff. Stay tuned for the original system!

← Older revision		Revision as of 17:36, 2 December 2024
Line 17:		Line 17:

	There is an Edwards EST3-6ANN annunciator in the main entrance vestibule.		There is an Edwards EST3-6ANN annunciator in the main entrance vestibule.

			===== Booster Panels =====
			There is an Edwards BPS6A booster power supply located next to the main fire alarm panel.

	====Notification Appliances====		====Notification Appliances====
	Most notification appliances are Edwards MB10-24 motor bells (10” gong) mounted on Edwards 403-5A-R strobe plates (15cd).		Most notification appliances are Edwards MB10-24 motor bells (10” gong) mounted on Edwards 403-5A-R strobe plates (15cd).

	Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).		Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).

			Some areas have Edwards 439D-10AWC vibrating bells (10" gong) mounted remotely; it is unknown if these are in use on the current system.
	===Initiating Devices===		===Initiating Devices===
	====Pull Stations====		====Pull Stations====
Line 28:		Line 34:

	Some patient rooms and all elevator shafts have Edwards SIGA-PD addressable photoelectric smoke detectors as deficiency replacements.		Some patient rooms and all elevator shafts have Edwards SIGA-PD addressable photoelectric smoke detectors as deficiency replacements.

			Some areas mentioned above have Edwards SIGA-OSD addressable optical smoke detectors as deficiency replacements.

	All other areas have Edwards SIGA-HRD or EST SIGA-HRS addressable 135°F fixed-temperature/rate-of-rise heat detectors. There is a 75/25 mix of HRD to HRS throughout.		All other areas have Edwards SIGA-HRD or EST SIGA-HRS addressable 135°F fixed-temperature/rate-of-rise heat detectors. There is a 75/25 mix of HRD to HRS throughout.

	All detectors are mounted on EST SIGA-SB bases.		All aforementioned detectors are mounted on EST SIGA-SB bases.

			There are EST SIGA-DH duct smoke detector housings with EST SIGA-PS addressable photoelectric heads and EST SIGA-SB bases on most air handling units: two on the second floor and one in the penthouse.
	====Modules====		====Modules====
	There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.		There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.

	There are EST SIGA-CR addressable relay modules serving various purposes.		There are EST SIGA-CR addressable relay modules serving various purposes.

			There is an EST SIGA-CRH addressable high-power relay module for primary elevator recall.

			There are EST SIGA-IM addressable isolator modules on some SLCs.

	==== EOLs ====		==== EOLs ====

TwentyThree33 at 17:45, 30 September 2024

2024-09-30T17:45:10Z

← Older revision		Revision as of 11:45, 30 September 2024
Line 5:		Line 5:
	\|		\|
	\|-		\|-
	\| FACP: Edwards EST3 <br />FACP Location: Maintenance Office <br />System Type: Addressable <br />System Line Voltage: 120VAC<br />NAC Voltage: 24VDC <br />System Coding: 20BPM (Alert) <br> Temporal (Alarm) <br>Strobes Synchronized: Yes, EST <br />Date of last known Upgrade: 2004 <br />Year Opened: 1982, 2004		\| FACP: Edwards EST3 <br />FACP Location: Maintenance Office <br />System Type: Two-Stage Addressable <br />System Line Voltage: 120VAC<br />NAC Voltage: 24VDC <br />System Coding: 20BPM (Alert) <br>Temporal (Alarm) <br>Strobes Synchronized: Yes, EST <br />Date of last known Upgrade: 2004 <br />Year Opened: 1982, 2004
	\|}		\|}
	The '''High River General Hospital''' is a hospital located at 560 9 Avenue Southwest, in High River, Alberta, Canada. The hospital is owned and operated by Alberta Health Services. The hospital was built in 1982, and was expanded in 2004. The fire alarm system was upgraded following the 2004 expansion.		The '''High River General Hospital''' is a hospital located at 560 9 Avenue Southwest, in High River, Alberta, Canada. The hospital is owned and operated by Alberta Health Services. The hospital was built in 1982, and was expanded in 2004. The fire alarm system was upgraded following the 2004 expansion.
Line 12:		Line 12:
	The building is protected by an Edwards EST3 addressable fire alarm system. The panel is located in the maintenance office. The system runs Edwards’ Signature addressable protocol, and is configured for two-stage operation. The alert coding is 20BPM, and the alarm coding is temporal.		The building is protected by an Edwards EST3 addressable fire alarm system. The panel is located in the maintenance office. The system runs Edwards’ Signature addressable protocol, and is configured for two-stage operation. The alert coding is 20BPM, and the alarm coding is temporal.
	=====Annunciators=====		=====Annunciators=====
	There are Edwards EST3-LCDANN annunciators at all nurse’s stations. The cancer centre annunciator is equipped with the Edwards LCDXL1 display; all others are equipped with the standard display. There is an Edwards EST3-6ANN annunciator in the main entrance vestibule.		There are Edwards EST3-LCDANN annunciators at all nurse’s stations.

			The cancer centre annunciator is equipped with the Edwards LCDXL1 display; all others are equipped with the standard display.

			There is an Edwards EST3-6ANN annunciator in the main entrance vestibule.
	====Notification Appliances====		====Notification Appliances====
	Most notification appliances are Edwards MB10-24 motor bells (10” gong) mounted on Edwards 403-5A-R strobe plates (15cd).		Most notification appliances are Edwards MB10-24 motor bells (10” gong) mounted on Edwards 403-5A-R strobe plates (15cd).

	Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).		Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).
	===Initiating Devices===		===Initiating Devices===
Line 20:		Line 25:
	All pull stations are EST SIGA-270P addressable two-stage single-action pull stations.		All pull stations are EST SIGA-270P addressable two-stage single-action pull stations.
	====Automatic Detection Devices====		====Automatic Detection Devices====
	There are EST SIGA-PS addressable photoelectric smoke detectors throughout all corridors and in all patient rooms. Some patient rooms and all elevator shafts have Edwards SIGA-PD addressable photoelectric smoke detectors as deficiency replacements.		There are EST SIGA-PS addressable photoelectric smoke detectors throughout all corridors and in all patient rooms.

			Some patient rooms and all elevator shafts have Edwards SIGA-PD addressable photoelectric smoke detectors as deficiency replacements.

	All other areas have Edwards SIGA-HRD or EST SIGA-HRS addressable 135°F fixed-temperature/rate-of-rise heat detectors. There is a 75/25 mix of HRD to HRS throughout.		All other areas have Edwards SIGA-HRD or EST SIGA-HRS addressable 135°F fixed-temperature/rate-of-rise heat detectors. There is a 75/25 mix of HRD to HRS throughout.

	All detectors are mounted on EST SIGA-SB bases.		All detectors are mounted on EST SIGA-SB bases.
	====Modules====		====Modules====
	There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.		There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.

	There are EST SIGA-CR addressable relay modules serving various purposes.		There are EST SIGA-CR addressable relay modules serving various purposes.

			==== EOLs ====
			There are Edwards EOL-P1 end of line resistor plates on all sprinkler and signal circuits.
	[[Category:Alberta]]		[[Category:Alberta]]
	[[Category:Healthcare]]		[[Category:Healthcare]]

TwentyThree33 at 23:28, 25 May 2024

2024-05-25T23:28:59Z

← Older revision		Revision as of 17:28, 25 May 2024
Line 7:		Line 7:
	\| FACP: Edwards EST3 <br />FACP Location: Maintenance Office <br />System Type: Addressable <br />System Line Voltage: 120VAC<br />NAC Voltage: 24VDC <br />System Coding: 20BPM (Alert) <br> Temporal (Alarm) <br>Strobes Synchronized: Yes, EST <br />Date of last known Upgrade: 2004 <br />Year Opened: 1982, 2004		\| FACP: Edwards EST3 <br />FACP Location: Maintenance Office <br />System Type: Addressable <br />System Line Voltage: 120VAC<br />NAC Voltage: 24VDC <br />System Coding: 20BPM (Alert) <br> Temporal (Alarm) <br>Strobes Synchronized: Yes, EST <br />Date of last known Upgrade: 2004 <br />Year Opened: 1982, 2004
	\|}		\|}
			The '''High River General Hospital''' is a hospital located at 560 9 Avenue Southwest, in High River, Alberta, Canada. The hospital is owned and operated by Alberta Health Services. The hospital was built in 1982, and was expanded in 2004. The fire alarm system was upgraded following the 2004 expansion.
	The '''High River General Hospital''' is a hospital located at 560 9 Avenue Southwest, in High River, Alberta, Canada. The hospital is owned and operated by Alberta Health Services. The hospital was built in 1982, and was expanded in 2004. The fire alarm system was upgraded following the 2004 expansion.

	==System Specifications (2004-present)==		==System Specifications (2004-present)==
	====FACP====		====FACP====
	The building is protected by an Edwards EST3 addressable fire alarm system. The panel is located in the maintenance office. The system runs Edwards’ Signature addressable protocol, and is configured for two-stage operation. The alert coding is 20BPM, and the alarm coding is temporal.		The building is protected by an Edwards EST3 addressable fire alarm system. The panel is located in the maintenance office. The system runs Edwards’ Signature addressable protocol, and is configured for two-stage operation. The alert coding is 20BPM, and the alarm coding is temporal.

	=====Annunciators=====		=====Annunciators=====
	There are Edwards EST3-LCDANN annunciators at all nurse’s stations. The cancer centre annunciator is equipped with the Edwards LCDXL1 display; all others are equipped with the standard display. There is an Edwards EST3-6ANN annunciator in the main entrance vestibule.		There are Edwards EST3-LCDANN annunciators at all nurse’s stations. The cancer centre annunciator is equipped with the Edwards LCDXL1 display; all others are equipped with the standard display. There is an Edwards EST3-6ANN annunciator in the main entrance vestibule.

	====Notification Appliances====		====Notification Appliances====
	Most notification appliances are Edwards MB10-24 motor bells (10” gong) mounted on Edwards 403-5A-R strobe plates (15cd).		Most notification appliances are Edwards MB10-24 motor bells (10” gong) mounted on Edwards 403-5A-R strobe plates (15cd).
	Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).		Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).

	===Initiating Devices===		===Initiating Devices===
	====Pull Stations====		====Pull Stations====
	All pull stations are EST SIGA-270P addressable two-stage single-action pull stations.		All pull stations are EST SIGA-270P addressable two-stage single-action pull stations.

	====Automatic Detection Devices====		====Automatic Detection Devices====
	There are EST SIGA-PS addressable photoelectric smoke detectors throughout all corridors and in all patient rooms. Some patient rooms and all elevator shafts have Edwards SIGA-PD addressable photoelectric smoke detectors as deficiency replacements.		There are EST SIGA-PS addressable photoelectric smoke detectors throughout all corridors and in all patient rooms. Some patient rooms and all elevator shafts have Edwards SIGA-PD addressable photoelectric smoke detectors as deficiency replacements.
	All other areas have Edwards SIGA-HRD or EST SIGA-HRS addressable 135°F fixed-temperature/rate-of-rise heat detectors. There is a 75/25 mix of HRD to HRS throughout.		All other areas have Edwards SIGA-HRD or EST SIGA-HRS addressable 135°F fixed-temperature/rate-of-rise heat detectors. There is a 75/25 mix of HRD to HRS throughout.
	All detectors are mounted on EST SIGA-SB bases.		All detectors are mounted on EST SIGA-SB bases.

	====Modules====		====Modules====
	There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.		There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.
	There are EST SIGA-CR addressable relay modules serving various purposes.		There are EST SIGA-CR addressable relay modules serving various purposes.
			[[Category:Alberta]]
			[[Category:Healthcare]]

TwentyThree33: Created page with "{| style="float:right;border:2px solid black" |- ! System Specifications |- | |- | FACP: Edwards EST3
FACP Location: Maintenance Office
System Type: Addressable <..."

2024-01-19T02:19:57Z

Created page with "{| style="float:right;border:2px solid black" |- ! System Specifications |- | |- | FACP: Edwards EST3 FACP Location: Maintenance Office System Type: Addressable <..."

New page

{| style="float:right;border:2px solid black"
|-
! System Specifications
|-
|
|-
| FACP: Edwards EST3 FACP Location: Maintenance Office System Type: Addressable System Line Voltage: 120VAC NAC Voltage: 24VDC System Coding: 20BPM (Alert) Temporal (Alarm) Strobes Synchronized: Yes, EST Date of last known Upgrade: 2004 Year Opened: 1982, 2004
|}

The '''High River General Hospital''' is a hospital located at 560 9 Avenue Southwest, in High River, Alberta, Canada. The hospital is owned and operated by Alberta Health Services. The hospital was built in 1982, and was expanded in 2004. The fire alarm system was upgraded following the 2004 expansion.

==System Specifications (2004-present)==
====FACP====
The building is protected by an Edwards EST3 addressable fire alarm system. The panel is located in the maintenance office. The system runs Edwards’ Signature addressable protocol, and is configured for two-stage operation. The alert coding is 20BPM, and the alarm coding is temporal.

=====Annunciators=====
There are Edwards EST3-LCDANN annunciators at all nurse’s stations. The cancer centre annunciator is equipped with the Edwards LCDXL1 display; all others are equipped with the standard display. There is an Edwards EST3-6ANN annunciator in the main entrance vestibule.

====Notification Appliances====
Most notification appliances are Edwards MB10-24 motor bells (10” gong) mounted on Edwards 403-5A-R strobe plates (15cd).
Newly renovated areas have System Sensor SSM24-6A motor bells (6” gong) mounted on Edwards 403-5A-R strobe plates (15cd).

===Initiating Devices===
====Pull Stations====
All pull stations are EST SIGA-270P addressable two-stage single-action pull stations.

====Automatic Detection Devices====
There are EST SIGA-PS addressable photoelectric smoke detectors throughout all corridors and in all patient rooms. Some patient rooms and all elevator shafts have Edwards SIGA-PD addressable photoelectric smoke detectors as deficiency replacements.
All other areas have Edwards SIGA-HRD or EST SIGA-HRS addressable 135°F fixed-temperature/rate-of-rise heat detectors. There is a 75/25 mix of HRD to HRS throughout.
All detectors are mounted on EST SIGA-SB bases.

====Modules====
There are EST SIGA-CT1 addressable monitor modules supervising the sprinkler system’s tamper and flow switches.
There are EST SIGA-CR addressable relay modules serving various purposes.