Miette Hot Springs: Difference between revisions

Latest revision as of 13:04, 13 October 2024

System Specifications

FACP: EST QuickStart QS4 FACP Location: Behind Front Desk System Type: Single-Stage Conventional System Line Voltage: 120VAC NAC Voltage: 24VFWR System Coding: Likely Temporal Date of last known Upgrade: 2010s Year Opened: 1986

Miette Hot Springs is a tourist attraction in Jasper National Park, AB. It is an outdoor hot pool with two pools. The building also has a restaurant, and a souvenir gift shop. The building was built in 1986, and the system was upgraded in 2007. Most of the notification appliances, one pull station and most smoke detectors are original.

System Specifications (1986-present)[edit | edit source]

FACP[edit | edit source]

The building is protected by an EST QuickStart QS4 conventional fire alarm system. The panel is located behind the front desk. The system coding is likely temporal.

The panel was installed in 2007, replacing an Edwards 2280.

Notification Appliances[edit | edit source]

All notification appliances except for one are Edwards 439D-6AWC vibrating bells (6" gong). These are original to the building.

There is a Notifier KMS-10-24A motor bell (10" gong) outside facing the pools as a deficiency replacement.

Initiating Devices[edit | edit source]

Pull Stations[edit | edit source]

All pull stations except for one are Mircom MS-401 conventional pull stations. Most were installed following the renovation, and there are a few newer variants as deficiency replacements.

There is one Edwards 270-SPOB conventional pull station by the staff room, which is likely original.

Automatic Detection Devices[edit | edit source]

There are System Sensor 1400A conventional ionization smoke detectors in some areas.

There is one System Sensor C2W-BA conventional photoelectric smoke detector as a deficiency replacement.

There are Edwards 281C conventional 135°F fixed-temperature/rate-of-rise heat detectors in some areas.

EOLs[edit | edit source]

There are Edwards EOL-P1 end of line resistor plates on all circuits.

@@ Line 1: / Line 1: @@
-'''Miette Hot Springs''' is a tourist attraction in Jasper National Park, AB. It is an outdoor hot pool with two pools. The building also has a restaurant, and a souvenir gift shop. Only most of the bells, and maybe one pull is original.
+{| style="float:right;border:2px solid black"
+|-
-== System Specifications ==
+! System Specifications
+|-
+|
+|-
+| FACP: EST QuickStart QS4 <br>FACP Location: Behind Front Desk<br />System Type: Single-Stage Conventional<br /> System Line Voltage: 120VAC<br />NAC Voltage: 24VFWR <br>System Coding: Likely Temporal<br />Date of last known Upgrade: 2010s <br />Year Opened: 1986
+|}
+'''Miette Hot Springs''' is a tourist attraction in Jasper National Park, AB. It is an outdoor hot pool with two pools. The building also has a restaurant, and a souvenir gift shop. The building was built in 1986, and the system was upgraded in 2007. Most of the notification appliances, one pull station and most smoke detectors are original.
+== System Specifications (1986-present) ==
 ==== FACP ====
+The building is protected by an EST QuickStart QS4 conventional fire alarm system. The panel is located behind the front desk. The system coding is likely temporal.
-The fire alarm control panel is an EST QuickStart QS1, from around 2003-2011. It likely replaced an older Edwards/EST panel, likely a 2280 or 6616. The fire alarm panel is located behind the front desk. Despite the QuickStart QS1 being an addressable fire alarm control panel, the system is set up in a non-addressable manner.
+The panel was installed in 2007, replacing an Edwards 2280.
 ==== Notification Appliances ====
+All notification appliances except for one are Edwards 439D-6AWC vibrating bells (6" gong). These are original to the building.
-Most of the notification appliances are older Edwards 439D-6AWC vibrating bells. These bells take 0.075 amps of current instead of the 0.085 amps which are seen in the 1990s-2013 models. The one in the lobby is mounted upside down. Outside where the pools are, there is a Notifier KMS-10-24A motor bell, replacing an older bell no longer functioning.
+There is a Notifier KMS-10-24A motor bell (10" gong) outside facing the pools as a deficiency replacement.
 === Initiating Devices ===
+==== Pull Stations ====
+All pull stations except for one are Mircom MS-401 conventional pull stations. Most were installed following the renovation, and there are a few newer variants as deficiency replacements.
-==== Pull Stations ====
+There is one Edwards 270-SPOB conventional pull station by the staff room, which is likely original.
+==== Automatic Detection Devices ====
+There are System Sensor 1400A conventional ionization smoke detectors in some areas.
-Most of the pull stations except for one are Mircom MS-401. They can range from pre-2014 and 2014-current models. It is unknown why they are there. The odd one out pull station is behind the front desk to a staff room, which is an Edwards 270-SPOB biligual pull station, possibly original.
+There is one System Sensor C2W-BA conventional photoelectric smoke detector as a deficiency replacement.
-==== Automatic Detection Devices ====
+There are Edwards 281C conventional 135°F fixed-temperature/rate-of-rise heat detectors in some areas.
-The smoke detectors were kept from the original fire alarm system. They are Edwards EDW1451A ionization smoke detectors. One was replaced with a System Sensor C2W-BA i3 photoelectric smoke detector. The heat detectors are all original, they are Edwards 280B-PL.
+==== EOLs ====
+There are Edwards EOL-P1 end of line resistor plates on all circuits.
 [[Category:Facilities]]
+[[Category:Alberta]]
+[[Category:Tourist Attractions]]